Trading | CRI Products | Submersible Pumps

C.R.I.'s horizontal open well submersible pumps are ideally suitable for open wells where there is a wide fluctuation in water level. This works under water and it rest at the bottom of the well. Pump portion is of single stage (horizontal pump) & single or multi stage (Vertical pump) and fitted with cast iron casing and impeller. Pump volute chamber is designed to give the best possible hydraulic efficiency. Dynamically balanced impeller offer vibration free operation with long life. Prime mover is eco friendly wet wound type water filled rewindable. The stator windings are of water proof synthetic film insulated copper winding wires. It features water lubricated thrust and journal bearing. Motor is pre filled with clear, cold, pure, fresh filtered water. Dynamically balanced rotor maintain uniform clearance thereby giving better efficiency and increase the life cycle of the water lubricated bush bearings. Specially designed high performance thrust bearings are used that can withstand high axial thrust loads and up thrust loads with wear and tear. Pressure equalizing rubber diaphragm is provided to guard against pressure and volume variations due to thermal expansion of water inside the motor. Motor sealing are made by means of 'O' rings, shaft seals and sand guard to prevent ingress of well water, sand and fibre particles in to the motor.

C.R.I’s Bottom Suction Pumps are close coupled type and available with multi impellers and motor is protected by double sealing system with and oil chamber. Stator portion is filled with non- toxic edible grade oil which serves as coolant and lubricant for rotor and bearings.

C.R.I. 6” & 8” Evergreen series submersible pumps are available with different material of construction. Pumps are incorporated with externally hardwearing bearing and built in Stainless Steel Check valve. All vital components of these pumps are designed for the best possible hydraulic efficiency. All the bronze components are made of zinc free bronze to resist corrosion and to withstand wear and tear caused by sand. The Shaft made of SS 431 ensures the long life of the pump. Pumps are multistage centrifugal type, which are firmly coupled to submersible electric motor which operates submerged beneath the surface of water. Built in check valve prevents the back flow and reduces the risk of water hammer. All mounting dimension of pump are accordance with NEMA standard.

.R.I. 6” & 8” Evergreen series submersible pumps are available with different material of construction. Pumps are incorporated with externally hardwearing bearing and built in Stainless Steel Check valve. All vital components of these pumps are designed for the best possible hydraulic efficiency. All the bronze components are made of zinc free bronze to resist corrosion and to withstand wear and tear caused by sand. The Shaft made of SS 431 ensures the long life of the pump. Pumps are multistage centrifugal type, which are firmly coupled to submersible electric motor which operates submerged beneath the surface of water. Built in check valve prevents the back flow and reduces the risk of water hammer. All mounting dimension of pump are accordance with NEMA standard.

C.R.I. 6" & 8" Evergreen series submersible pumps are available with different material of construction. Pumps are incorporated with externally hardwearing bearing and built in Stainless Steel Check valve. All vital components of these pumps are designed for the best possible hydraulic efficiency. All the bronze components are made of zinc free bronze to resist corrosion and to withstand wear and tear caused by sand. The Shaft made of SS 431 ensures the long life of the pump. Pumps are multistage centrifugal type, which are firmly coupled to submersible electric motor which operates submerged beneath the surface of water. Built in check valve prevents the back flow and reduces the risk of water hammering. All mounting dimension of pump are accordance with NEMA standard.

C.R.I. 3" & 4" Silver Line Series submersible pumps are built with thermoplastic impellers, diffusers and inbuilt check valve. All vital components of these pumps are made of corrosive resistance thermoplastic and the shaft is of SS 304/431. Pumps are multi stage centrifugal type. The optimal design of impellers and diffusers enables the best possible hydraulic efficiency. The pump is firmly coupled to a submersible electric motor which operates submerged beneath the surface of water. Built in check valve prevents back flow and reduces the risk of water hammering. All mounting dimensions are in accordance with NEMA Standard motors.

C.R.I. 4",6",8" & 10" Stainless steel series submersible pumps are made of corrosion resistance stainless steel with built in check valve.All vital components are made of high quality 304/316 grade stainless steel and the shaft is SS 304/329/431. The optimal design of impellers and diffusers enables the best possible hydraulic efficiency. These pumps are of mulistage centrifugal type, which can be firmly coupled to a submersible electric motor, which operates submerged beneath the surface of water. Built in check valve prevents back flow and reduces the risk of water hammer. All mounting dimensions of pumps are in accordance with NEMA standards. These Pumps can be offered with C.R.I. water filled rewindable/ Oil filled / Resin filled encapsulated submersible motors or any other NEMA standard motors